electricity - What happens when we connect a metal wire between the 2 poles of a battery?

As I remembered, at the 2 poles of a battery, positive or negative electric charges are gathered. So there'll be electric field existing inside the battery. This filed is neutralized by the chemical power of the battery so the electric charges will stay at the poles.

Since there are electric charges at both poles, there must also be electric fields outside the battery. What happens when we connect a metal wire between the 2 poles of a battery? I vaguely remembered that the wire has the ability to constrain and reshape the electric field and keep it within the wire, maybe like an electric field tube. But is that true?

Answer

Yes Sam, there definitely is electric field reshaping in the wire. Strangely, it is not talked about in hardly any physics texts, but there are surface charge accumulations along the wire which maintain the electric field in the direction of the wire. (Note: it is a surface charge distribution since any extra charge on a conductor will reside on the surface.) It is the change in, or gradient of, the surface charge distribution on the wire that creates, and determines the direction of, the electric field within a wire or resistor.

For instance, the surface charge density on the wire near the negative terminal of the battery will be more negative than the surface charge density on the wire near the positive terminal. The surface charge density, as you go around the circuit, will change only slightly along a good conducting wire (Hence the gradient is small, and there is only a small electric field). Corners or bends in the wire will also cause surface charge accumulations that make the electrons flow around in the direction of the wire instead of flowing into a dead end. Resistors inserted into the circuit will have a more negative surface charge density on one side of the resistor as compared to the other side of the resistor. This larger gradient in surface charge distribution near the resistor causes the relatively larger electric field in the resistor (as compared to the wire). The direction of the gradients for all the aforementioned surface charge densities determine the direction of the electric fields.

This question is very fundamental, and is often misinterpreted or disregarded by people. We are all indoctrinated to just assume that a battery creates an electric field in the wire. However, when someone asks "how does the field get into the wire and how does the field know which way to go?" they are rarely given a straight answer.

A follow up question might be, "If nonzero surface charge accumulations are responsible for the size and direction of the electric field in a wire, why doesn't a normal circuit with a resistor exert an electric force on a nearby pith ball from all the built up charge in the circuit?" The answer is that it does exert a force, but the surface charge and force are so small for normal voltages and operating conditions that you don't notice it. If you hook up a 100,000V source to a resistor you would be able to measure the surface charge accumulation and the force it could exert.

Here's one more way to think about all this (excuse the length of this post, but there is so much confusion on this question it deserves appropriate detail). We all know there is an electric field in a wire connected to a battery. But the wire could be as long as desired, and so as far away from the battery terminals as desired. The charge on the battery terminals can't be directly and solely responsible for the size and direction of the electric field in the part of the wire miles away since the field would have died off and become too small there. (Yes, an infinite plane of charge, or other suitably exotic configurations, can create a field that does not decrease with distance, but we are not talking about anything like that.) If the charge near the terminals does not directly and solely determine the size and direction of the electric field in the part of the wire miles away, some other charge must be creating the field there (Yes, you can create an electric field with a changing magnetic field instead of a charge, but we can assume we have a steady current and non-varying magnetic field). The physical mechanism that creates the electric field in the part of the wire miles away is a small gradient of the nonzero surface charge distribution on the wire. And the direction of the gradient of that charge distribution is what determines the direction of the electric field there.

For a rare and absolutely beautiful description of how and why surface charge creates and shapes the electric field in a wire refer to the textbook: "Matter and Interactions: Volume 2 Electric and Magnetic Interactions" by Chabay and Sherwood, Chapter 18 "A Microscopic View of Electric Circuits" pg 631-640.